MODIFICATION

DEFENDER 2.2 DE-CAT PIPE This De-cat pipe for 2.2 Defenders will make the vehicle breathe better and also stop excessive heat from the cat coming into the vehicle.

Enhance the performance of your Td5 engine by replacing the restricting inlet manifold with this kit. The kit comes complete with a new intercooler hose fitting, gasket, bolts and plate.

POWER SPEC TD5 SOLID MASS FLYWHEEL KIT The power spec is ideal if you use your Land Rover as a work horse. If you want reliability and drivability from your mapped upgraded motor and turbo. When your clutch needs replacing you won't need to replace the flywheel.

Discovery 3 Auxiliary Transmission Cooler Fits all Discovery 3 Models.

The Eaton TVS supercharger fitted to 5.0 Range Rover Rover models is an excellent compressor, which can be easily upgraded by changing the pulley.  This increases the driven speed of the supercharger, which in turn increasing boost pressure by about 2.5psi, and allowing the engine to produce more power without the strain of revving higher.

When tackling a ledge or attacking steep descent’s, you always run the risk of damaging your Defender's rear end, especially on the 110 wheel base. The Bumperette's act as corner protectors, protecting both the vehicle's body & tail lights while also providing a step For roof top access.  

Fits ALL DEFENDERS, DISCOVERY 1 1989 - 1998 and RANGE ROVER CLASSIC. Increase the body clearance to allow the fitment of really big tyres as well as provide an additional 50mm of lift to your suspension. These simple spacers bolt between the coil spring and the axle and can be the perfect way to lift the vehicle to the desired ride height when the load or equipment carried exceeds even the heaviest rated coil springs.

NOTE: Please advise in the comments section when ordering if vehicle is Defender or Discovery 2 to recieve the correct fitting kit. NOTE: YOUR ORIGINAL CENTRIFUGE DRAIN PIPE REQUIRED BACK FOR EXCHANGE. The Provent system is designed to stop crank case oil vapour recycling back...

RANGE ROVER SPORT ELECTRONIC HEIGHT CONTROL KIT The Llams electronic air suspension height controller allows selection of off-road and high-speed   heights at any speed.

The edge of the Defender seat box is prone to damage, protect that edge and smarten up your interior with these protectors. Made from 2mm stainless steel and CNC cut for accuracy. Less than 5 minutes to fit and all you need is a drill for the fixings. Kit includes a pair of corner protectors and steel self drill fixings.

The POWER PEDAL SPRING is 45% stronger and lighter than the Land Rover over-centre spring as fitted to the TDi vehicles. 45% lighter than OEM pedal assist spring. 80% lighter than no spring at all when retro fitted to TD5 / 300TDi Defender.

The factory Tie Down point on a Discovery 2 is NOT a recovery point. Thats why at Davis Performance we turned the Factory Tie Down Point into a Heavy Duty Recovery Point. We take a factory Tie Down Point, shape & weld solid steel onto The Tie Down Point. A block of solid steel is also fitted to...

The standard Defender Td5 is a great car, but can feel lethargic and be somewhat frustrating when it doesn't deliver the power you'd expect. With an DPL remap we make your Defender feel brighter and more responsive, delivering the power exactly where you need it, and with our socially acceptable tuning, without any nasty smoke!

Consists of:1x Glass gullwing door assembly1x Outer frame1x Fastening kit2x Gas struts1x Right side inner bracket1x Left sideinner bracket1x Top inner bracket1x Bottom inner bracketMaterials used:6mm Toughened glass with tinted laminateBlack powder-coated high strength steelProduct Dimensions:Overall: L 1120mm (44.1) x W 50mm (2) x H 490mm (19.3)Door Panel: L 1044mm (41.1) x H 414mm (16.3)Weight:15kg (33.1lbs) Glass specifications: Visible Light:Transmission: 44Reflection Outside: 5 Solar Energy:Total Elimination: 38Reflection Outside: 5Absorption 1: 47Direct Transmission: 47SHGC: 0.62 Shading Coefficient:Ratio: 0.71 U Value:(W/m2).K (Center of Glass): 5.8

Consists of:1xAluminium gullwing door assembly1x Outer frame1x Fastening kit2x Gas struts1x Right side inner bracket1x Left side inner bracket1x Top inner bracket1x Bottom inner bracketMaterials used:Black powder-coated 3mm aluminiumBlack powder-coated 2mm mild steel reinforcement plateBlack powder-coated high strength steelProduct Dimensions:Overall: L 1120mm (44.1) x W 50mm (2) x H 490mm (19.3)Door Panel: L 1044mm (41.1) x H 414mm (16.3)Weight:15.5kg (34.2lbs)

RANGE ROVER ELECTRONIC HEIGHT CONTROL KIT The Llams electronic air suspension height controller allows selection of off-road and high-speed   heights at any speed.

DEFENDER TD5 DE-CAT PIPE This De-cat pipe for TD5 Defenders will make the vehicle breathe better and also stop excessive heat from the cat coming into the vehicle.

Sealing washers for TD5 gasket. Used on both 10P and 15P engines. 13 Needed for complete set.

For Discovery 2’s with rear air suspension this simple kit will increase ground clearance and tyre to body clearance. If the rear air springs are to be retained to maintain the self-levelling facility these spacer kits are the perfect solution for achieving a 50mm lift. The front kit compliments the rear perfectly.

Discovery 4 Auxiliary Transmission Cooler Fits all Discovery 4 Models.

DEFENDER 2.4 DE-CAT PIPE This De-cat pipe for 2.4 Defenders will make the vehicle breathe better and also stop excessive heat from the cat coming into the vehicle.